Updated Nov 17, 2026· 7 min read

Key takeaways

  • Automatic versus manual: Automatic switches sense an outage and transfer by themselves. Manual switches are operated by a person.
  • Open transition: The switch breaks one source before making the other, so there is a brief interruption. Closed-transition and delayed-transition designs are other options that makers offer.
  • Service-entrance rated: The switch can serve as the main disconnect for the building. A non-service-rated switch is installed downstream of a main disconnect.
  • Bypass isolation: A design that allows the transfer mechanism to be isolated for maintenance without losing power.
  • Poles: Two, three or four poles, depending on whether the neutral is switched.
  • Withstand and closing rating (WCR): The fault current the switch is rated to withstand, which must meet or exceed the available fault current.

A 600-amp transfer switch is commercial and industrial switchgear, not a retail product: it is specified by an engineer, ordered through a distributor and installed by licensed electricians, and a typical house has a 100- to 400-amp service, so a homeowner will rarely need one. The confirmed current 600-amp families are Generac’s RTSC600A3 (single-phase 120/240 V) and RTSN600 series (three-phase), Generac’s TX301 commercial series, and the 600-amp-capable KCS, KSSB, KAS and KAP lines from Kohler’s industrial power systems range, now branded Rehlko. If you are sizing a switch for a large home, farm or small business, the right first step is a load calculation and a conversation with an electrical contractor.

What a 600-amp transfer switch does

A transfer switch moves an electrical load between two sources, usually the utility and a generator, and prevents the two from being connected at once. This protects line workers from back-feed and protects equipment from damage. A 600-amp rating means the switch can carry that current continuously, subject to the maker’s stated conditions. At 240 volts single-phase, 600 amps corresponds to a very large load; commercial buildings often use three-phase service at 208, 480 or 600 volts. The switch must match the system voltage, number of phases, number of poles and the available fault current at the location.

Key terms you will see

  • Automatic versus manual: Automatic switches sense an outage and transfer by themselves. Manual switches are operated by a person.
  • Open transition: The switch breaks one source before making the other, so there is a brief interruption. Closed-transition and delayed-transition designs are other options that makers offer.
  • Service-entrance rated: The switch can serve as the main disconnect for the building. A non-service-rated switch is installed downstream of a main disconnect.
  • Bypass isolation: A design that allows the transfer mechanism to be isolated for maintenance without losing power.
  • Poles: Two, three or four poles, depending on whether the neutral is switched.
  • Withstand and closing rating (WCR): The fault current the switch is rated to withstand, which must meet or exceed the available fault current.

At a glance

Product Stated specs Application Notes
Generac RTSC600A3 600 A non-service-rated, open-transition switch for 120/240 V single phase; NEMA 3R enclosure; 42,000 A withstand rating; 1/0 to 500 MCM lug range; transfer time 160 ms; 5-year limited warranty Works with Generac’s 22 to 150 kW liquid-cooled generators, per the maker Not service rated, so a separate main disconnect is needed; designed as part of a Generac system
Generac RTSN600G3 and RTSN600K3 600 A non-service-entrance three-phase switch; NEMA 3R enclosure; 2-year limited warranty Three-phase standby systems Read the spec sheet for voltage and generator pairing
Generac TX301 series 600 A at up to 600 VAC, 60 Hz, 100 percent current rated; single or three phase; 2, 3 or 4 poles; NEMA 1 or 3R; open and in-phase, or open with delayed transition; ETL listed to UL 1008; the service-entrance version lists a 100 kA rating at up to 480 V Commercial buildings Specified by a design professional
Kohler / Rehlko KCS (Standard, Open) 30 to 4000 A; 2, 3 or 4 poles; MPAC controllers; a KCS 600 open page is listed Commercial and industrial Open transition
Kohler / Rehlko KSSB 30 to 1200 A; NEMA 1, 3R, 4, 4X and 12 enclosures Commercial and industrial Ask a distributor for the 600 A configuration
Kohler / Rehlko KAS and KAP Bypass isolation, 150 to 600 A Where maintenance without a shutdown matters Maker lists as bypass-isolation lines
Kohler / Rehlko KUS and KUP Service entrance; KUS 70 to 4000 A and KUP 150 to 4000 A Service-entrance applications Local utility and code rules apply

The main families

The Generac RTSC600A3 figures below come from the maker’s spec sheet. The TX301 and Kohler or Rehlko details come from category-level pages, so treat them as a starting point and have a distributor or engineer confirm the exact configuration and ratings.

Generac residential and light commercial

The RTSC600A3 is a non-service-rated, open-transition switch for 120/240-volt single-phase systems. Generac states it works with its 22 to 150 kilowatt liquid-cooled generators and lists a NEMA 3R enclosure, a 42,000-amp withstand rating, a lug range of 1/0 to 500 MCM, a transfer time of 160 milliseconds and a five-year limited warranty. The three-phase RTSN600G3 and RTSN600K3 are 600-amp non-service-entrance switches with NEMA 3R enclosures and a two-year limited warranty. These switches are matched with the maker’s generator controllers, so confirm the exact pairing with the manufacturer or an authorized dealer. The RTSC600A3 spec sheet notes it is not service rated, so it sits downstream of a separate main disconnect.

Generac TX301 commercial series

Generac’s published listing says the TX301 series is rated 600 amps at up to 600 volts AC, 60 hertz, and is 100 percent current rated. It comes in single or three phase, with two, three or four poles and NEMA 1 or 3R enclosures, in open in-phase or open delayed-transition designs, and it is ETL listed to UL 1008. A service-entrance-rated version lists a 100,000-amp rating at up to 480 volts. These are for commercial systems and are chosen by a design engineer.

Kohler and Rehlko

Kohler’s industrial power systems range, now under the Rehlko name, lists automatic transfer switches from 30 to 4000 amps in standard, bypass-isolation and service-entrance configurations, with open, programmed and closed transition options, using the maker’s MPAC controllers. The KCS family covers 30 to 4000 amps with two, three or four poles, and a KCS 600 open product page exists. The KSSB covers 30 to 1200 amps in several enclosure types. The KAS and KAP bypass-isolation lines cover 150 to 600 amps, and the KUS and KUP service-entrance lines cover higher ranges. The residential RXT line seen in the same results was a 200-amp part, so for 600 amps look at the industrial lines.

What to decide before buying

  • System voltage and phase: Single phase 120/240 V, or three phase at 208, 240, 480 or 600 V. The switch must match.
  • Generator pairing: Makers specify which generators and controllers their switches work with. Mixing brands needs engineering input.
  • Service-entrance or not: This depends on where the switch sits in the electrical system and local code.
  • Transition type: Open transition has a brief interruption; programmed or closed transition options reduce or manage it, but may need utility approval.
  • Short-circuit rating: The switch rating must meet or exceed the available fault current at its location.
  • Enclosure: NEMA 1 for indoors, 3R for outdoors, and other types for harsh environments.
  • Lugs and conductors: The Generac RTSC600A3 lists 1/0 to 500 MCM lugs. Conductor size, number of parallel runs and terminal capacity all need to be checked by the designer.
  • Weight and space: Large switches are heavy and need clearances, mounting and conduit routing.

Safety and code notes

This is high-energy equipment. Installation, commissioning, testing and maintenance must be done by qualified, licensed personnel following the manufacturer’s manual, the applicable electrical code and the local authority’s requirements, including permits and inspections. Do not attempt to open or service a switch while energized. Do not defeat interlocks or safety devices. A generator connected without proper transfer equipment can back-feed the utility grid and endanger line workers. Utilities may also have their own interconnection rules.

Budget, mid-range and premium tiers

Because every 600-amp switch is a major installation, tiers are better described by scope. A budget project is a non-service-rated, open-transition switch paired with a standby generator from the same maker, such as Generac’s RTSC600A3. A mid-range project adds service-entrance rating or a three-phase configuration. A premium project adds bypass isolation, closed transition and custom controls, as in Kohler’s bypass-isolation lines and commercial series. Costs are driven by installation, permits, engineering and the generator itself, more than by the switch alone.

Pick X if …

If you want… Pick Why
A large single-phase home or farm backup system Generac RTSC600A3 120/240 V single phase, designed to pair with the maker’s 22 to 150 kW generators
A three-phase 600 A switch in a Generac system Generac RTSN600G3 or RTSN600K3 Three-phase, NEMA 3R, non-service-entrance
A commercial switch with UL 1008 listing Generac TX301 series 600 A at up to 600 VAC; ETL listed to UL 1008
Maintenance without losing power Kohler / Rehlko KAS or KAP Bypass isolation, 150 to 600 A
A broad range of configurations Kohler / Rehlko KCS or KSSB Standard open transition in many sizes and enclosures
A smaller home service A 200 A or smaller switch Most homes do not need 600 A

Alternatives

  • Smaller automatic transfer switches: Generac lists a 200-amp automatic switch (G0099410) and other sizes for residential services.
  • Load management: Splitting essential and non-essential loads can reduce the needed switch rating. An engineer can design this.
  • Manual transfer switches: Lower cost and simpler, but they need a person to operate them.

Frequently Asked Questions

Can a homeowner buy a 600-amp transfer switch?

It is available through distributors and dealers, but it is commercial or industrial equipment that needs engineering and licensed installation. Most homes do not need 600 amps, so a load calculation is the right first step.

What is the difference between service-rated and non-service-rated?

A service-rated switch can act as the main disconnect for the building, while a non-service-rated switch sits downstream of a separate main disconnect. Local code and the utility determine which is needed.

What does open transition mean?

The switch disconnects from one source before connecting to the other, so there is a brief interruption. Generac lists a 160 millisecond transfer time for its RTSC600A3.

Can I use any generator with any transfer switch?

No. Makers specify compatible generators and controllers. Generac says the RTSC600A3 works with its 22 to 150 kW liquid-cooled generators. Confirm pairing with the manufacturer.

Do I need a permit?

Most jurisdictions require permits and inspection for transfer switches and generators, and the utility may need to be notified. A licensed electrician or contractor handles this.

What is the withstand rating for?

It states the fault current the switch can handle safely. It must meet or exceed the available fault current where the switch is installed, which an engineer determines.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.